T/CAEPI 73-2023 预荷电脉冲袋式除尘器技术要求

ICS13.040.30

CCSC70

团体标准

T/CAEPI73—2023

预荷电脉冲袋式除尘器技术要求

Technicalrequirementsforpre⁃chargedpulsebaghouse

2023⁃08⁃31发布2023⁃10⁃01实施

中国环境保护产业协会发布

中国标准出版社出版

T/CAEPI73—2023

目次

前言··························································································································Ⅲ

1范围·······················································································································1

2规范性引用文件········································································································1

3术语和定义··············································································································2

4命名·······················································································································2

5技术要求·················································································································3

6检验方法·················································································································8

7检验规则·················································································································9

8标志及随行文件······································································································10

9包装、运输和贮存·····································································································11

Ⅰ

T/CAEPI73—2023

前言

本文件按照GB/T1.1—2020《标准化工作导则第1部分：标准化文件的结构和起草规则》的规

定起草。

请注意本文件的某些内容可能涉及专利。本文件的发布机构不承担识别专利的责任。

本文件起草单位：中钢集团天澄环保科技股份有限公司、中国环境保护产业协会。

本文件主要起草人：姚群、孙军军、闫骏、倪守强、许汉渝、陈志炜、韩宗秋、叶超、吕璐、余建华、

赵霞、陈立、范驰、刘立。

本文件主要审议人：孙熙、陈隆枢、赵江翔、蔡伟龙、姚宇平、姚芝茂、姜宏、沈玉祥、费传军、吕维宁。

本文件由中国环境保护产业协会负责管理，由起草单位负责具体技术内容的解释。在应用过程中

如有需要修改与补充的建议，请将相关资料寄送至中国环境保护产业协会标准管理部门（北京市西城

区二七剧场路6号2层，邮编100045）。

Ⅲ

T/CAEPI73—2023

预荷电脉冲袋式除尘器技术要求

1范围

本文件规定了预荷电脉冲袋式除尘器的命名、技术要求、检验方法、检验规则及其标志、包装、运

输、贮存等。

本文件适用于钢铁、有色、机械、建材、工业锅炉等重点工业行业炉窑烟气细颗粒物去除用预荷电

脉冲袋式除尘器的制造，其他行业工业烟气细颗粒物去除用预荷电脉冲袋式除尘器可参照执行。

2规范性引用文件

下列文件中的内容通过文中的规范性引用而构成本文件必不可少的条款。其中，注日期的引用文

件，仅该日期对应的版本适用于本文件；不注日期的引用文件，其最新版本（包括所有的修改单）适用于

本文件。

GB/T191包装储运图示标志

GB/T700碳素结构钢

GB/T706热轧型钢

GB/T985.1气焊、焊条电弧焊、气体保护焊和高能束焊的推荐坡口

GB/T2828.1计数抽样检验程序第1部分：按接收质量限（AQL）检索的逐批检验抽样计划

GB/T3274碳素结构钢和低合金结构钢热轧钢板和钢带

GB4053.1固定式钢梯及平台安全要求第1部分：钢直梯

GB4053.2固定式钢梯及平台安全要求第2部分：钢斜梯

GB4053.3固定式钢梯及平台安全要求第3部分：工业防护栏杆及钢平台

GB/T5117非合金钢及细晶粒钢焊条

GB/T6388运输包装收发货标志

GB/T6719袋式除尘器技术要求

GB/T8923.1涂覆涂料前钢材表面处理表面清洁度的目视评定第1部分：未涂覆过的钢材

表面和全面清除原有涂层后的钢材表面的锈蚀等级和处理等级

GB/T9174一般货物运输包装通用技术条件

GB/T9286色漆和清漆划格试验

GB/T9969工业产品使用说明书总则

GB/T13277.1压缩空气第1部分：污染物净化等级

GB/T13306标牌

GB/T13384机电产品包装通用技术条件

GB/T16845除尘器术语

GB/T28699钢结构防护涂装通用技术条件

GB/T32154电袋复合除尘器性能测试方法

GB50011建筑抗震设计规范

GB50034建筑照明设计标准

GB50205钢结构工程施工质量验收标准

1