GB/T 19660-2005 工业自动化系统与集成机床数值控制 坐标系和运动命名

ICS25.040.20

J50

中华人民共和国国家标准

GB/T19660-2005/ISO841:2001

工业自动化系统与集成

机床数值控制坐标系和运动命名

Industrialautomationsystemsandintegration-

Numericalcontrolofmachines-

Coordinatesystemandmotionnomenclature

(ISD841:2001，IDT)

2005-01-25发布2005-06-01实施

中华人民共和国国家质量监督检验检疫总局

中国国家标准化管理委员会发布

GB/T19660-2005/ISO841:2001

目次

前言··································································，·············，，·······························……m

1范围····························································，······，··········································……7

2规范性引用文件······························································..···········…1

3术语和定义·····，································································································……1

4机床坐标系······································································································……1

4.1名称············，···························································································……1

4.2原点··························，·················································································……1

4.3Z轴··············，···，························································································……1

4.4X轴············································································································……2

4.5Y轴····························································，···············································……2

4.6回转轴A,B和C·················································································……2

5机床的主要运动································································································……2

5.1名称···········································································································……2

5.2方向··········································································································……2

6附加运动·······································································································……3

6.1直线运动······································································································……3

6.2回转运动······································································································……3

6.3字母限制······································································································……3

6.4方向··················……，···················································································……3

7机床示意图·····································································································……3

7.1机床图例······································································································……3

7.2说明············································································································……3

附录A(规范性附录)机床运动图例····································································……4

GB/T19660-2005/ISO841:2001

Fiji吕

本标准等同采用ISO841;2001((工业自动化系统与集成机床数值控制坐标系和运动命名肛英

文版)。

本标准等同翻译ISO841:2001,

为便于使用，本标准做了下列编辑性修改:

a)用本“标准”代替本“国际标准”。

b)删除了ISO841:2001的前言和引言。

c)删除了规范性引用文件中的引导语，用GB/T1.1-200。中6.2.3规定的引导语代替。

d)对于ISO841:2001引用的其他国际标准中有被等同采用为我国标准的，本标准用引用我国的

国家标准代替对应的国际标准，其余没有等同采用为我国标准的国际标准，在本标准中均直接引用。

本标准是在JB/T3051-1999数《控机床坐标和运动方向命名》(eqvISO841:1974)基础上进行

制定的，与原标准相比，在技术内容上做了必要的调整和补充:

a)内容进行了调整，逻辑性更强。

b)轴和运动的区别更加清楚。

c)增加了新的机床类型

d)增加了复杂机床的运动名称。

本标准的附录A为规范性附录。

本标准由中国机械工业联合会提出。

本标准由全国工业自动化系统与集成标准化技术委员会物理设备控制分委会归口。

本标准起草单位