GB/T 19520.10-2004 电子设备机械结构 482.6mm(19in)系列机械结构尺寸 第5-105部分：插箱及其插件 定位/接地销

ICS31.240

K05}Ga

中华人民共和国国家标准

GB/T19520.10-2004/IEC60297-5-105:2001

电子设备机械结构

482.6mm(19in)系列机械结构尺寸

第5-105部分:插箱及其插件定位/接地销

Mechanicalstructuresforelectronicequipment-

Dimensionsofmechanicalstructuresofthe482.6mm(19in)series-

Part5-105:Subracksandassociatedplug-inunits-Alignmentand/orearthpin

(IEC60297-5-105:2001,IDT)

2004-05-14发布2005-02-01实施

中华人民共和国国家质量监督检验检疫总局发布

中国国家标准化管理委员会

GB/T19520.10-2004/IEC60297-5-105:2001

目次

前言·，·，·······‘····，····，··············································-·················，，·················……工

引言.·II

1范围·······································································································。·······……1

2规范性引用文件····································，······································。，·················，·……1

3术语和定义··············。··········，，·············，······································，·，···············……2

4在GB/T19520.3和GB/T19520.4基础上增加的扩展特性·······································……2

5设备一般配置··················2

6设备配置细节··································································································，……3

7不小于4倍水平格距((4HP)的印制板式擂件的定位/接地销·，，，······································……4

7.1不小于4倍水平格距(4HP)的印制板式插件的定位/接地销在插箱导轨中的擂孔位置·····……4

7.2定位/接地销及定位/接地销插孔的检验尺寸··································，·····················……5

图1设备一般配置—前后安装具有定位/接地销的印制板式插件的典型6U插箱··········‘···……3

图2设备配置细节的设计··········，··········，····】··········。·····】······，·，，·，，······，··一·3

图3前/后安装插箱导轨中的定位/接地销插孔位置·················································……4

图4前安装擂件的擂箱定位/接地销的擂孔位置·························································……4

图5后安装插件的擂箱定位/接地销的插孔位置·················。·······································……5

’图6前/后安装擂箱和印制板式擂件定位/接地销和插孔的检验尺寸································一·5

表1插箱定位/接地销插孔和印制板式插件定位/接地销的检验尺寸

GB/T19520.10-2004/IEC60297-5-105:2001

前言

GB/T19520《电子设备机械结构482.6mm(19in)系列机械结构尺寸》分为以下几部分:

第1部分:面板和机架

第2部分:机柜和机架结构的格距

第3部分:插箱及其插件

第4部分:插箱及其插件附加尺寸

第5-100部分:插箱及其插件设计概述

第5-101部分:插箱及其插件插拔器手柄

第5-102部分:擂箱及其插件电磁屏蔽结构

第5-103部分:擂箱及其插件静电放电防护

第5-104部分:插箱及其插件编码键

第5-105部分:插箱及其插件定位/接地销

第5-107部分:插箱及其擂件后安装插件

本部分为GB/T19520的第5-105部分。

本部分等同采用IEC60297-5-105:2001《电子设备机械结构482.6mm(19in)系列机械结构尺寸

第5-105部分:插箱及其插件定位/接地销》(英文版)。

为便于使用，本部分作了下列编辑性修改:

a)“本标准”一词改为“本部分”;

b)删除了国际标准的前言。

本部分由中国电器工业协会提出。

本部分由全国电工电子设备结构综合标准化技术委员会